Rapid qualitative profiling and quantitative analysis of Juglandis Mandshuricae Cortex and seven flavonoids by ultra-high performance liquid chromatography–quadrupole/orbitrap high-resolution mass spectrometry

Juglandis Mandshuricae Cortex is the bark of Juglans mandshurica Maxim., which has been used as a folk medicine plant in China and India. In this study, an ultra-high performance liquid chromatography–quadrupole/orbitrap high-resolution mass spectrometry method was developed to clarify and quantify the chemical profiling of Juglandis Mandshuricae Cortex rapidly. A total of 113 compounds were characterized. Among them, seven flavonoids were simultaneously quantified in 15 min, including myricetin, myricetrin, taxifolin, kaempferol, quercetin, quercitrin, and naringenin. The method was validated for accuracy, precision, and the limits of detection and quantification. All calibration curves showed a good linear relationship (r > 0.9990) within test ranges. The intra- and inter-day relative standard deviations were less than 2.16%. Accuracy validation showed that the recovery was between 95.6 and 101.3% with relative standard deviation values below 2.85%. The validated method was successfully applied to determine the contents of seven flavones in Juglandis Mandshuricae Cortex from seven sources and the contents of these places were calculated respectively. This method provides a theoretical basis for further developing the medicinal value of Juglandis Mandshuricae Cortex.     

Enhanced thermoelectric performance of PEDOT:PSS films via ionic liquid post-treatment

Thermoelectric(TE)energy harvesting can effectively convert waste heat into electricity,which is a crucial technology to solve energy concerns.As a promising candidate for energy conversion,poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate)(PEDOT:PSS)has gained significant attention owing to its easy doping,high transparency,and solution processability.However,the TE performance of PEDOT:PSS still needs to be further enhanced.Herein,different approaches have been applied for tuning the TE properties:(i)direct dipping PEDOT:PSS thin films in ionic liquid;(ii)post-treatment of the films with concentrated sulfuric acid(H₂SO₄),and then dipping in ionic liquid.Besides,the same bis(trifluoromethanesulfonyl)amide(TFSI)anion and different cation salts,including 1-ethyl-3-methylimidazolium(EMIM+)and lithium(Li+),are selected to study the influence of varying cation types on the TE properties of PEDOT:PSS.The Seebeck coefficient and electrical conductivity of the PEDOT:PSS film treated with H2SO4EMIM:TFSI increase simultaneously,and the resulting maximum power factor is 46.7μW·m^-1·K^-2,which may be attributed to the ionic liquid facilitating the rearrangement of the molecular chain of PEDOT.The work provides a reference for the development of organic films with high TE properties.     

Dynamic Modeling of the Feed Drive System of a CNC Metal Cutting Machine

Studying the vibrational behavior of feed drive systems is important for enhancing the structural performance of computer numerical control (CNC) machines. The preload on the screw and nut position have a great influence on the vibration characteristics of the feed drive as two very important operational conditions. Rotational acceleration of the screw also affects the performance of the CNC feed drive when machining small parts. This paper investigates the influence of preload and nut position on the vibration characteristics of the feed drive system of a CNC metal cutting machine in order to be able to eliminate an observed resonance occurred at high rotational speeds of the screw, corresponding to high feed rates. Additionally, rational structural parameters of the feed drive system are selected in order to increase the rotational acceleration for improving the performance of the CNC machine. Experiments and analyses showed that by selecting specific parameters of feed drive system and simultaneously applying a certain value of preload, a 97% increase in rotational acceleration and 30% time reduction considering the vibration resistance at high rotational speeds can be achieved.     

Surfactant self-assembly structures and multilayer formation at the solid-solution interface induces by electrolyte,polymers and proteins

Recent developments in the study of the formation of self-assembled surfactant structures and multilayers at the solid-solution interface are presented. It covers a wide range of phenomena, but in this review the main focus is on the surface structures formed from dilute solution in the presence of electrolyte and in more concentrated solutions. Their formation under those conditions are set in the wider context of the more extensive observations of their occurrence in more complex polymer-surfactant mixtures. Although the sequential adsorption methods using layer-by-layer approaches are more well established for polyelectrolytes and their associated mixtures, the main emphasis is on the self-assembly. The opportunities to manipulate wetting properties and to generate enhanced wetting characteristics are discussed. The potential applications, modifying wetting behaviour, efficient near surface reservoir for enhanced and prolonged delivery of active components, and for the development of a range of smart functionalised surfaces are highlighted.     

水热法制备二氧化锡/钨酸铋复合光催化材料及其催化活性研究

本文用水热法制备了正交晶系的纳米球状结构的二氧化锡和正交晶系的由片状聚集成球状结构的钨酸铋,并且对二者进行了复合,制备出了二氧化锡/钨酸铋复合光催化材料。采用X射线衍射(XRD)、扫描电子显微镜(SEM)、比表面积测试仪(BET)、紫外可见分光光度计等技术对复合样品的结构、形貌、比表面积、孔容孔径和光学性质进行了表征。用碘钨灯模拟太阳光,分别以二氧化锡、钨酸铋和二氧化锡/钨酸铋复合材料为催化剂降解罗丹明B(RhB),研究所制备的二氧化锡/钨酸铋复合材料的光催化活性。光催化90 min时二氧化锡、钨酸铋和二氧化锡/钨酸铋对罗丹明B的降解率分别是9%、22%和30%。实验结果表明,在可见光下,二氧化锡/钨酸铋复合材料的光催化活性要高于单一的二氧化锡和钨酸铋。     

基于NiCo2O4纳米片电极的非对称混合电容器

The looming global energy crisis and ever-increasing energy demands have catalyzed the development of renewable energy storage systems. In this regard, supercapacitors (SCs) have attracted widespread attention because of their advantageous attributes such as high power density, excellent cycle stability, and environmental friendliness. However, SCs exhibit low energy density and it is important to optimize electrode materials to improve the overall performance of these devices. Among the various electrode materials available, spinel nickel cobaltate (NiCo₂O₄) is particularly interesting because of its excellent theoretical capacitance. Based on the understanding that the performances of the electrode materials strongly depend on their morphologies and structures, in this study, we successfully synthesized NiCo₂O₄ nanosheets on Ni foam via a simple hydrothermal route followed by calcination. The structures and morphologies of the as-synthesized products were characterized by X-ray diffraction, scanning electron microscopy, and Brunauer-Emmett-Teller (BET) surface area analysis, and the results showed that they were uniformly distributed on the Ni foam support. The surface chemical states of the elements in the samples were identified by X-ray photoelectron spectroscopy. The as-synthesized NiCo₂O₄ products were then tested as cathode materials for supercapacitors in a traditional three-electrode system. The electrochemical performances of the NiCo₂O₄ electrode materials were studied and the area capacitance was found to be 1.26 C·cm^-2 at a current density of 1 mA·cm^-2. Furthermore, outstanding cycling stability with 97.6% retention of the initial discharge capacitance after 10000 cycles and excellent rate performance (67.5% capacitance retention with the current density from 1 to 14 mA·cm^-2) were achieved. It was found that the Ni foam supporting the NiCo₂O₄ nanosheets increased the conductivity of the electrode materials. However, it is worth noting that the contribution of nickel foam to the areal capacitance of the electrode materials was almost zero during the charge and discharge processes. To further investigate the practical application of the as-synthesized NiCo₂O₄ nanosheets-based electrode, a device was assembled with the as-prepared samples as the positive electrode and active carbon (AC) as the negative electrode. The assembled supercapacitor showed energy densities of 0.14 and 0.09 Wh·cm^-3 at 1.56 and 4.5 W·cm^-3, respectively. Furthermore, it was able to maintain 95% of its initial specific capacitance after 10000 cycles. The excellent electrochemical performance of the NiCo₂O₄ nanosheets could be ascribed to their unique spatial structure composed of interconnected ultrathin nanosheets, which facilitated electron transportation and ion penetration, suggesting their potential applications as electrode materials for high performance supercapacitors. The present synthetic route can be extended to other ternary transition metal oxides/sulfides for future energy storage devices and systems.     

Coupling nanoliter high‐performance liquid chromatography to inductively coupled plasma mass spectrometry for arsenic speciation

Nanoliter high‐performance liquid chromatography shows low consumption of solvents and samples, offering one of the best choices for arsenic speciation in precious samples in combination with inuctively coupled plasma mass spectrometry. A systematic investigation on coupling nanoliter high‐performance liquid chromatography to inductively coupled plasma mass spectrometry from instrument design to injected sample volume and mobile phase was performed in this study. Nanoflow mobile phase was delivered by flow splitting using a conventional high‐pressure pump with reuse of mobile phase waste. Dead volume was minimized to 60 nL for the sheathless interface based on the previously developed nanonebulizer. Capillary columns for nanoliter high‐performance liquid chromatography were found to be sensitive to sample loading volume. An apparent difference was also found between the mobile phases for nanoliter and conventional high‐performance liquid chromatography. Baseline separation of arsenite, arsenate, monomethylarsenic, and dimethylarsenic was achieved within 11 min on a 15 cm C₁₈ capillary column and within 12 min on a 25 cm strong anion exchange column. Detection limits of 0.9–1.8 μg/L were obtained with precisions variable in the range of 1.6–4.2%. A good agreement between determined and certified values of a certified reference material of human urine (GBW 09115) validated its accuracy along with good recoveries (87–102%).     

Facile preparation of Ag/Ag2WO4/g‐C3N4 ternary plasmonic photocatalyst and its visible‐light photocatalytic activity

Introducing plasmonic metals into semiconductor materials has been proven to be an attractive strategy for enhancing photocatalytic activity in the visible region. In this work, a novel and efficient Ag/Ag₂WO₄/g‐C₃N₄ (AACN) ternary plasmonic photocatalyst was successfully synthesized using a facile one‐step in situ hydrothermal method. The composition, structure, morphology and optical absorption properties of AACN were investigated using X‐ray diffraction, Fourier transform infrared spectroscopy, scanning electron microscopy, and UV–visible diffuse reflectance spectroscopy, respectively. Photocatalytic performance of AACN was evaluated via rhodamine B and tetracycline degradation. The results indicated that AACN had excellent photocatalytic performance for rhodamine B degradation with a rate constant of 0.0125 min^?1, which was higher than those of Ag₂WO₄ and Ag/Ag₂WO₄. Characterization and photocatalytic tests showed that the strong coupling effect between the Ag/Ag₂WO₄ nanoparticles and the exfoliated ultrathin g‐C₃N₄ nanosheets was superior for visible‐light responsivity and reduced the recombination rate of photogenerated electrons and holes. A proposed mechanism is also discussed according to the band energy structure and the experimental results.     

Inhibition effect of butan-1-ol on the corrosion behavior of austenitic stainless steel (Type 304) in dilute sulfuric acid

The electrochemical behavior of austenitic stainless steel (Type 304) in 3 M sulfuric acid with 3.5% recrystallized sodium chloride at specific concentrations of butan-1-ol was investigated with the aid of potentiodynamic polarization, open circuit measurement and weight loss technique. Butan-1-ol effectively inhibited the steel corrosion with a maximum inhibition efficiency of 78.7% from weight-loss analysis and 80.9% from potentiodynamic polarization test at highest concentration studied. Adsorption of the compound obeyed the Freundlich isotherm. Thermodynamic calculations reveal physiochemical interactions and spontaneous adsorption mechanism. Surface characterizations showed the absence of corrosion products and topographic modifications of the steel. Statistical analysis depicts the overwhelming influence and statistical significance of inhibitor concentration on the inhibition performance.     

原位合成Bi3O4Br/Bi12O17Br2光催化剂及其对磺胺甲噁唑降解性能

Bi_xO_yBr_z光催化剂在有机药物废水处理领域有着非常广阔的潜在应用价值,但因光生电子和空穴的快速复合而表现出较低的光催化效率,进而限制了其应用范围。通过简易的水解-焙烧法原位制得一种新型的Bi₃O₄Br/Bi₁₂O₁₇Br₂复合光催化剂,并以磺胺甲噁唑(SMX)为模拟药物污染物进行了光催化性能测试,对所制催化剂进行了X射线衍射(XRD)、X射线光电子能谱(XPS)、扫描电子显微镜(SEM)、紫外可见漫反射光谱(UV-Vis DRS)、电化学阻抗(EIS)、光致发光光谱(PL)等表征。结果表明所制备的Bi₃O₄Br/Bi₁₂O₁₇Br₂复合光催化剂具有较强的光生载流子分离率、较低的界面电荷转移电阻,进而展示出优异的光催化降解SMX性能,在模拟太阳光下照射30 min,SMX降解率达到87%,相较于纯的Bi₃O₄Br和Bi₁₂O₁₇Br₂催化剂,降解率分别提升了30%和24%。最后基于自由基捕获实验和催化剂能带结构分析了所制催化剂的降解机理。